Marmitek RC840 Dokumentacja Pobierz pdf (Strona 105)

BATTERY REPLACEMENT (RC840)

When the battery is low, the RC840’s LED flashes during transmission.

To replace the battery:

1. Remove the battery cover located at the rear of the unit. To do so, press the

release tab using a small screwdriver and lift the cover away from the RC840’s

plastic housing.

2. Observing correct polarity, replace the battery (9V, alkaline).

3. Replace the battery cover making sure that it clicks shut.

9V Alkaline

Battery

Fig 0

(

ure B.16: RC84

battery cover off)

ProGuard800™ -105-

1 2 ... 100 101 102 103 104 105 106 107 108 109 110 111 112

Safety Warnings 2
Table of Contents 3
ProGuard800™ -5 5
Chapter One: Introduction 6
1.2: Specifications 7
1.3: System Overview 7
1.4: Hardware Layout 9
Figure 1.3: Main Board 10
ProGuard800™ -11 11
ProGuard800™ -13 13
2.2: Installation Procedure 14
ProGuard800™ -15 15
2.3: Back Tamper 17
3.1: Front Panel Layout 19
3.2: System Status LEDs 19
3.3: Front Panel Keypad 20
3.4: LCD Display 20
ProGuard800™ -21 21
3.7: Arming/Disarming 23
ProGuard800™ -25 25
FuLl A r m#1234121 26
FULL A RM ED- M A RK 26
ProGuard800™ -27 27
4.1: Menu Navigation 28
4.2: Stop Communications 28
4.4: User Codes 29
4.5: Follow Me 31
4.6: Event Log 31
4.7: Service Menu 32
ProGuard800™ -33 33
ZONE #2 34
ProGuard800™ -35 35
5.1: Incoming Calls 37
5.2: Outgoing Calls 39
ProGuard800™ -41 41
6.1: Keypad Control 42
6.2: Keyfob Control 42
6.3: Telephone Control 42
6.4: Scheduling 43
Table 6.1: Weekly Schedule 44
Chapter Seven: Devices 45
7.4: Supervision Time 46
7.5: Re-Synchronization 46
7.6: Zones 46
ProGuard800™ -47 47
7.7: Keyfobs 49
7.8: Keypads 50
7.9: Repeaters 51
7.10: Wireless Siren 51
8.1: Entry/Exit Delay 53
8.2: Arm on Exit 53
8.4: Entry Deviation 54
8.5: Exit Restart 54
8.6: Arming Tones 54
8.7: Home Automation Tones 55
8.8: System Trouble Tones 55
8.9: Tones Options 56
Chapter Nine: System Options 57
9.4: Panic Alarm 59
9.5: AC Loss Delay 59
9.6: Display Options 60
9.7: PGM Output Options 61
9.9: “No Arm” Indication 62
9.10: Jamming Detection 62
9.11: “No Motion” Time 63
9.13: Vocal Messages 63
9.14: Installer Access 63
9.16: Daylight Savings 64
9.17: Report Fail Trouble 64
9.18: Cancel Alarm 64
9.20: Verified Fire 65
9.21: Battery Type 65
Chapter Ten: Communications 66
ProGuard800™ -67 67
10.3: Vocal Message Dialler 68
ProGuard800™ -69 69
10.4: Remote Programming 70
ProGuard800™ -71 71
10.5: Service Call 72
10.6: Communications Options 72
ProGuard800™ -73 73
10.7: GSM Options 75
ProGuard800™ -77 77
ProGuard800™ -79 79
11.1: X-10 Overview 80
11.2: HA Units 80
ProGuard800™ -81 81
11.3: House Code 83
11.4: HA Control 83
12.1: Initialization 84
12.3: Clear User Codes 84
12.5: Find Modules 85
Appendix A: Menu Structure 86
ProGuard800™ -87 87
ProGuard800™ -89 89
ProGuard800™ -91 91
PIR Sensors (MS845) 93
ProGuard800™ -95 95
Magnetic Contact (DS831) 96
ProGuard800™ -97 97
Glass break Sensor (GB843) 99
Figure B.7: GB843 (cover off) 100
ProGuard800™ -101 101
Smoke Detector (SD833) 102
Keyfobs (PR811/KR814) 103
Figure B.13: WK820 104
Figure B.14: RC840 104
ProGuard800™ -105 105
Transmitter Specifications 106
Appendix C: Event Table 107
Appendix D: Zone Types 109
Declaration of Conformity 111

Komentarze do niniejszej Instrukcji

Brak uwag

Marmitek RC840 Dokumentacja Strona 105

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Marmitek RC840